Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation: The Miami Owner’s Guide

Ghost Controls access control installation in Miami typically runs $340 to $690 installed, depending on whether we’re wiring a new keypad or card reader, replacing a failed control board, or adding a vehicle loop detector to an existing gate. Most jobs are finished the same day we arrive, since our trucks carry Ghost Controls-compatible boards, receivers, keypads, and safety-edge parts. You’ll usually know something’s wrong when the gate stops responding to the remote, the keypad goes dark, or the opener cycles but won’t hold a signal. In Miami’s humidity and salt air, we see corroded control board terminals and fried power supplies more than anything else, and those failures show up as intermittent operation before they become a dead gate.

Call (850) 409-8032

Key takeaways:

• Typical installed cost in Miami: $340 – $690, fully quoted in writing before work starts.
• Same-day replacement available for most Ghost Controls access control parts.
• Every installation carries the 365-Day Done Right Promise, written on the invoice.
• We stock Ghost Controls-compatible boards, receivers, keypads, and safety accessories on the truck.
• Call (850) 409-8032 for a free estimate, day or night.

Which Ghost Controls Models This Applies To

Ghost Controls builds swing and slide gate opener kits under a few main series: the AXS, AXP, AXD, and the heavier TSS and TDS lines. The access control installation side of those systems covers the receiver board, the wired keypad or digital entry panel, vehicle loop detectors, safety photo eyes, and the battery backup module that keeps everything running when Miami’s summer storms knock out power. If your control board has a model number starting with AXC or AXS printed on the label, you’re looking at a Ghost Controls proprietary board that talks to their specific receiver. Aftermarket generic boards sometimes work, but we’ve seen enough intermittent failures from mismatched aftermarket receivers that we default to Ghost Controls OEM or direct-compatible replacements unless a customer asks otherwise.

The model number lives on a silver sticker on the side of the operator arm or inside the control box. Take a photo before you call us. It saves a trip. And one thing we see in Coral Gables, Pinecrest, and along the older neighborhoods in the Grove: original Ghost Controls installs from 10 or 12 years ago often have a receiver board that’s no longer produced. When that’s the case, we quote the retrofit kit that replaces the receiver and antenna together, which runs about $120 more than a straight board swap. We’ll tell you that before we touch anything.

Portcullis Gate Repair Miami is an independent service provider, not affiliated with Ghost Controls. We also stock parts for LiftMaster, Mighty Mule, and DoorKing systems.

Signs Your Ghost Controls Access Control Installation Is Failing

• The remote works only from five feet away. Ghost Controls receivers lose range when the antenna wire corrodes or the board’s solder joints start cracking from South Florida heat cycling. You’ll notice it works fine in the morning and barely responds by afternoon.
• The keypad lights up but the gate won’t move. That points to a dead relay on the keypad’s output circuit, or a broken wire between the keypad and the control board. We find ants nesting in keypad enclosures more often than you’d believe.
• The gate opens on its own or won’t stay closed. A failing loop detector or a safety eye that’s drifting out of alignment can trick the board into thinking a car is waiting. Sometimes it’s enough to clean the photo eye lens; sometimes the detector board needs replacement.
• You hear a clicking sound but nothing moves. The control board’s relay is firing but the operator’s motor or capacitor isn’t responding. On Ghost Controls units from the last eight years or so, we often find the 12V battery backup has swollen from heat and shorted the charging circuit.
• After a power blink, all your remotes and codes are gone. Memory loss after a surge usually means the control board’s EEPROM chip got hit. We replace the board and re-program all your remotes in one visit.

Replacement Cost & What’s Included

For a Ghost Controls access control installation in Miami, you’re generally looking at:

• Receiver board replacement: $340 – $490 installed.
• Wired keypad or digital entry panel (new wiring run not included): $280 – $420 installed.
• Vehicle loop detector and one saw-cut loop in the driveway: $460 – $690 installed.
• Safety photo eye pair, aligned and tested: $240 – $360 installed.
• Battery backup module replacement: $280 – $390 installed.
• Full access control retrofit (board, receiver, keypad, loop detector, safety eyes): $1,100 – $1,800 depending on gate size and wire condition.

Every price is a written price, given to you before we start. No surprises at the door. Parts and labor are line-itemed on the invoice, and the whole job falls under the Kingswell Guarantee. That means a real arrival window, a clean job site, and a 365-day written guarantee on the repair. If it fails within that year, we come back and fix it at no charge. That’s the core of how we work at Portcullis Gate Repair Miami, and Dean Prescott has held that line since he first started turning wrenches in the trade.

DIY or Call Us?

There are a few things you can safely check yourself before calling. Look at the receiver board’s small LED indicator. If it’s dark and the unit has power, note that. Check the keypad for moisture, ants, or corroded terminals. Look at the photo eyes on either side of the gate and see whether one of the lenses is clouded or the bracket got bumped by a mower. Those checks help us diagnose faster. What we don’t recommend is opening the control box and probing around with a multimeter. Ghost Controls boards carry live 12V and sometimes 120V input on the same board, and reversing polarity on the wrong terminal can fry the board and the receiver in one touch. That turns a $340 repair into a $900 one. If the gate isn’t responding reliably, call us at (850) 409-8032. Tell me what it’s doing and I’ll tell you what it needs, usually before I even pull out a wrench.

FAQs